Subscribing... Tom Metro (tmetro+ubuntu) wrote on 2009-03-31: #42 Tormod Volden wrote: > The seven first comments indicate that this is a harmless warning and that things otherwise > work well. Do the Leaves of Lórien brooches have any special significance or attributes? Note that registered members see fewer ads, and ContentLink is completely disabled once you log in. his comment is here
IvD 01-05-2008 17:13:52 You should have the "edit" button visible on each post in a thread. Alvin Cura (alvinc) wrote on 2007-09-29: #5 zipfile of strace logs Edit (25.0 KiB, application/zip) Ah ha! "strace -ff -F -o out ifup eth1:1" does the trick. The two bugs may have a common underlying cause, but superficially they have different symptoms. Wired ... http://www.linuxquestions.org/questions/slackware-14/ip-alias-siocsifflags-cannot-assign-requested-address-912985/
ping: sendmsg: Operation not permitted I experienced similar errors few times before (with routerboard-based AP) and solution was put switch between device and router. This seems like a good suggestion. But it seems that ubuntu-desktop is a metapackage, so it's ok to remove it. The error message really had me going until I found this report.
Alternatively, doing (as root) "make install" copies the firmware file and also creates an alias in /etc/modprobe.d/ralink (2.6 kernels) or /etc/modules.conf (2.4 kernels). I know pretty much input up to here, but I really, really googled and tried a lot to get it working. yenn View Public Profile View LQ Blog View Review Entries View HCL Entries Find More Posts by yenn Thread Tools Show Printable Version Email this Page Search this Thread Advanced Linux Connect Cannot Assign Requested Address what the hell are doing those ubuntu develoers?
Any ideas? Siocsifflags: Cannot Assign Requested Address Redhat Slim Amamou (slim-amamou) wrote on 2010-02-03: #47 I have the same problem in 9.10 Karmic. Ubuntu 16.04 installer cant see SSD drive Why "silver-tongued" for someone who is convincing? http://askubuntu.com/questions/423530/cant-change-my-mac-address-cant-assign-requested-address This bug deals with virtual interfaces triggering a "SIOCSIFFLAGS: Cannot assign requested address" warning, while still succeeding, and can be remedied by removing or patching the /etc/network/if-pre-up.d/wireless-tools file.
So I don't have any good suggestions on how to resolve this for Ubuntu 8.04 LTS, but given the significant impact it's reported to have for server users in certain configurations, Siocsifnetmask Cannot Assign Requested Address Ubuntu Is this still an issue in Intrepid Alpha 6? last night, i try to use rt73 module from k2wrlz and I've ported to kernel 2.6.25. Maybe, because of the interface doesn't has a MAC address before ifup and it can't be triggered with ifup/usb_rtusb_open() before a MAC address is assigned.
Mikael Sjöberg (misjob) wrote on 2010-10-06: #50 remove: auto eth0:0 DinkyDogg (dinkydogg) wrote on 2010-12-09: #51 Problem still exists in Ubuntu 10.04 server. Picking 10 distinct words 'randomly' from List of unique words What is this line of counties voting for the Democratic party in the 2016 elections? Siocsifflags Cannot Assign Requested Address Ubuntu I will continue to investigate the source of the problem. Siocsifflags Cannot Assign Requested Address Debian In my config # ip addr add 192.168.1.13/24 dev eth1 does nothing - ifconfig: [....] eth1 Link encap:Ethernet HWaddr 5C:F3:FC:E5:F0:22 inet addr:192.168.1.11 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0
yenn View Public Profile View LQ Blog View Review Entries View HCL Entries Find More Posts by yenn 11-15-2011, 09:45 AM #4 yenn Member Registered: Jan 2011 Location: Czech this content Adam Reply to: firstname.lastname@example.org Adam Aube (on-list) Adam Aube (off-list) References: ifconfig eth0:1 up, says - Cannot assign requested address From: Deboo
I was adding an extra static ip address to an ubuntu server installation. device unplugged 2. Slim Amamou (slim-amamou) wrote on 2010-02-03: #49 removing wireless-tools did not solve the problem for me. weblink Top TrevorH Forum Moderator Posts: 17092 Joined: 2009/09/24 10:40:56 Location: Brighton, UK 'Cannot assign requested address' error on setting up ip-ran Quote Postby TrevorH » 2011/08/06 00:12:01 Since I'd never seen
What's wrong? Siocsifhwaddr Cannot Assign Requested Address Introduction to Linux - A Hands on Guide This guide was created as an overview of the Linux Operating System, geared toward new users as an exploration tour and getting started removing this allowed the aliases to come up at boot.
It works for me. I've created Bug #351378 to track the issue where DHCP fails to work for a virtual interface, when a DHCP client is used directly, or indirectly via the /etc/network/interfaces config file, Support LQ: Use code LQ3 and save $3 on Domain Registration Blogs Recent Entries Best Entries Best Blogs Blog List Search Blogs Home Forums HCL Reviews Tutorials Articles Register Search Search Rtnetlink Answers: Cannot Assign Requested Address It works fine, but I can't set IP alias eth0:0 Code: [email protected]:~# ifconfig eth0:0 172.16.172.1 netmask 255.255.255.0 up SIOCSIFFLAGS: Cannot assign requested address I also tried simple tests (on different NIC's),
The reason: I want to run a BIND on 2 machines with 2 separate IP addresses and on shared (service) IP address. The seven first comments indicate that this is a harmless warning and that things otherwise work well. With a hight log-level? http://tcsmacs.net/cannot-assign/ifup-eth0-cannot-assign-requested-address.php On both of them, I have DHCP working on eth0, and a static alias on eth0:0.
P.S As usual, I can't do this. Join them; it only takes a minute: Sign up Here's how it works: Anybody can ask a question Anybody can answer The best answers are voted up and rise to the Therefore I got an PCMCIA Card enabling USB 2.0 for this laptop. Nevertheless this did not solve the problem.
I don't have any Wireless network adapters, so I just did this: chmod a-x /etc/network/if-pre-up.d/wireless-tools This removes the execute permission from the wireless-tools file which disables it from being called and I tried to set IP address via 'ip' before, in case it would work Code: $ ip address add 172.16.172.1/24 dev eth0 [...] $ ip address delete 172.16.172.1/24 dev eth0 and should I increase the debug level up to 31 as suggested in the TESTING file, which ships with the driver? Why is it happening?