life sucks wear a helmet m590 10 posts since Sep 2003 Community Member 14Contributors 35Replies 36Views 13 YearsDiscussion Span 9 Years Ago Last Post by John A 0 Discussion Starter m590 tried my IPS COX recommendation to disconnect the power for about 1 minute then try again with no luck. Thanks for your help =) May 5, 2009 #11 (You must log in or sign up to reply here.) Show Ignored Content Topic Status: Not open for further replies. I hooked the AP up to port 1 and no lights or anything... get redirected here
All of the lights on the front of the router act normally. Make Google your friend too. I have also tried 192.168.0.1 View 8 Replies Similar Messages: Linksys Wired Router :: WRT610N - Cannot Access Wireless Router Through BEFSR41 Linksys Wireless Router :: WRT610N Isn't Able To Connect If it doesn't work from there you can find the DNS servers from your linksys router status page. https://community.linksys.com/t5/Wired-Routers/BEFSR41-v2-1-can-t-connect-to-router/td-p/613032
To learn more and to read the lawsuit, click here. colborisI also forgot to tell you that if that course of action failed type the http address in the run command, other than that you must check again those ISPs. You can change that 2 to a 3 and then the Linksys address will not be in your DHCP pool. I tried the same and nothing.
BleepingComputer is being sued by Enigma Software because of a negative review of SpyHunter. Had it all working, then when I tried to access the router (going between the computer and the router only using an ethernet cord, disconnecting from the Internet) so I could Now, as before the reset, I can connect to my router just fine via Wi-Fi (I have several devices connected this way) but none of the computers that I attempt to I can connect both comps succesfully to other router via the gigabit ports but not to this one.
But when i try to setup my wired media server it will not connect. Linksys Router Setup Page you cannot be on a VPN config and access it, log off that, becasue under VPN you are using works special net config and not your local one.2. It's been in storage (top shelf of a closet) for the last two years and when it when it was last used it worked like a pro. I also had an oldNetgear wireless router hooked up as a second router (via ethernet cable to it's WAN port),which I placed it in the center of my house to provide
thittmeierOct 10, 2012, 4:58 AM I am having the same problem when I do an IPCONFIG it says my IP Address is 70.95..240.17I have tried all of the reset suggestions and http://www.bleepingcomputer.com/forums/t/524680/need-help-connecting-to-wireless-router-used-as-access-point/ Linksys Wireless Router :: How To Connect Two Cisco WRT610N Linksys Wireless Router :: WRT610N - Unable To Connect New Devices To Network Linksys Wireless Router :: Unable To Connect Asus Can't Access Linksys Router I can connect our computers directly to the cable modem, and also thrumy oldwired Linksys router, but keep running into a dead end with my wireless router. 192.168 1.1 Linksys Router hadi1985May 3, 2012, 6:07 AM I did the resseting thing, but it didnt worked.
Edited by Torvald, 17 February 2014 - 09:46 PM. Get More Info Ask ! I can't seem to open the WRT54G's access (192.168.1.1) because (I thin) the new DLINK uses a local set of IPs that are 192.168.0.1xx.I can login to the NAS using its Attached Files ipconfig release screenshot.txt 1.05KB 3 downloads ipconfig renew screenshot.txt 1.05KB 3 downloads Google is my friend. 192.168.1.1 No Data Recieved
Any suggestions? View 1 Replies View Related Linksys Wireless Router :: E4200 Cannot Connect With Wired LAN Sep 27, 2011 I have this E4200 for about 3 months and allways has been used I also think you have sense of humor with the name aeinstein 0 aeinstein 79 13 Years Ago Reviewed by: SCboog, from SC Date reviewed: 13-May-03 Strengths: statistics noted are good useful reference No, create an account now.
View 3 Replies View Related Linksys Wired Router :: Befsr41 - 2nd PC Cannot Connect To Internet May 12, 2011 I have 2 PCs and am using a Linksys befsr41 router.The 192.168.1.1 Didn’t Send Any Data. Oct 10, 2011 To connect my new "smart tv" with my wireless linsys WRT610N, smart tv ask to take off all protection such as firewall and antivirus. disconnect from the Modem, disconnect the router from the modem and connect the PC to the router; you should be able to PING 192.168.1.1 if so, use your browser with http:
Personally, I assume the router is broken. I can ping the router at 192.168.1.1. TechSpot is a registered trademark. The 192.168.1.1 Page Isn’t Working So the xbox 360 is definitely seening the 5.0 network.
Since my ISP claims to be providing us with 15Mbps max downstream internet service, this should hopefully speed up our family's intenet access (once it getds here and is hooked up). The modem should be connected on the WAN port (left hand side as you look at the rear) and the iMac should be connected to port 1,2,3 or 4. However, i still counldn't talk to the wireless router to make any more changes to it. (Don't really need to make any more changes - just hate to lose the ability this page The connection problem aside, the router was a breeze to set up and has been working without any other problems.